APRIMATIC ONDA 801 PDF

aprimatic onda e z16 aprimatic onda aprimatic aprimatic xt aprimatic xt 44 installazione aprimatic zt4b service service aprimatic at par. Onda Электромеханический привод для откатных ворот массой до кг собственностью компании APRIMATIC S.p.a. и не могут быть. This manual. Product description. Kit indianapolis Wave kit for sliding doors and residential use condominiale. The kit includes: n ° 1 gearmotor degree Onda ;.

Author: Moogurg Goltishura
Country: Cuba
Language: English (Spanish)
Genre: Photos
Published (Last): 9 April 2012
Pages: 196
PDF File Size: 15.32 Mb
ePub File Size: 11.67 Mb
ISBN: 818-1-70312-380-2
Downloads: 60116
Price: Free* [*Free Regsitration Required]
Uploader: Gardasar

With internal control unit Adjustable torque limiter clutch on fast shaft.

The wheels must be appropriate to the type of slides used. The wheels must match the guide profile and must be in good condition. Aprimatic supplies different types of wheels; the sizes and relative capacities are indicated in figure B3.

When choosing the wheels, apart from the bearing, it must be considered that greater is the diameter, better is the sliding movement of the gates. D – Aprimatic microprocessor control unit shelter, where possible, from atmospheric agents or inside the geared-motor Note: With wooden gates, aprkmatic is better to use the plastic rack by verifying the good conditions of the wood in the fixing points.

In some areas where heavy snow occurs or there are flooding risks the geared-motor can be placed at a height of cm. A description is also given of the typical layout that must be controlled when the site is inspected see also fig. C11 for the layout and the positioning of the rack. ATTENTION It is essential that, when the site is inspected, the installer makes aprmiatic that there is sufficient room near the gate for the layouts illustrated in the drawings. The geared-motor must be correctly aligned with the gate guide, aprimatjc the correct distance from the gate, at the right depth, and the electric cable passage bore in the correct position C2.

Foundation plate positioning Execute a hole for the fitting of the cables for 30 mm diameter tubes MAX. Refer to them when mounting the cover see D8 page The A measurement depends on the type of pinion and the type of rack used see tables in C A – Plastic rack with a steel core B – Galvanized Steel rack In both, the length of each piece is 1 m.

It is simple to install without the need of welding. The plastic rack is normally fixed to the gate with screws. Four self-tapping screws for each piece are provided in the kit which are fitted as in C The threaded supports must be welded to the gate C It is advisable to weld the aprimahic circumference. C 19 Spirit ondda C 20 Rest the first rack section on the geared-motor pinion and move the spacers in contact with the gate until the first hole complete with screw and spacer is lined up with the vertical axis of the pinion C19then fix the spacer to aprimstic gate with a spot weld.

  78L24 DATASHEET PDF

The T2B control unit can be also installed inside the geared motor; in these case see further instruction in appendix. It is activated by two metal plates D3 that are fitted on the rack and come into onnda with the switch in the fully open and fully closed gate positions D4.

Move the gate to the closed position leaving sufficient space to guarantee the braking distance and safety clearance. Follow the same procedure for the open end travel plate. The adjustment of the clutch and all the safety devices must be per- formed only by qualified personnel.

The clutch intervenes by limiting the pressure of the gate on any obstacle in its path. The fixing bolts are the same used in the box of the control unit.

The release system that disengages the pinion allows the manual opening of the gate. To release the geared-motor just insert the triangular key F1 in the special lock and turn it half way round in a clockwise direction; In order to lock it, perform the operation in reverse order and aptimatic correct engaging by pushing the gate a few apgimatic.

To avoid incorrect manoeuvres and the consequent risk of accidents, it is important to read this manual carefully, strictly observing the instructions given.

Device for Aprimatic operators to operate swing gates. Device with Aprimatic microprocessor 15 Watt in stand-by designed to drive 1 motor with a maximum power of Watt. Secure the device at a minimum height of 30 cm, using the securing holes in the plastic container. Insert the connecting cables, through the holes in the bottom of the container and the cable clamps indicated.

The adjustment range of the pause time apfimatic between 0 and seconds. Standard Automatic Immediate re-closure Trimmer P2 – This trimmer is used to adjust the intensity of the electronic brake, to Page of aprimahic Go.

Le informazioni sono dirette agli operatori esperti che eseguono l’installazione e la manutenzione straordinaria. Essi devono possedere competenze specifiche. This manual has been prepared by the manufacturer and is an integral part of the product. The information is aimed at expert installers and those carrying out extraordinary arimatic operations. These persons must be specifically qulified to carry out this work aprimatiic and under the maximum safety conditions.

  DESTETE VENTILATORIO PDF

Scrupulous observance of the instructions will ensure safety for man, economic running and a long product functioning life. To avoid incorrect manoeuvres and. As this is a product to be installed in residential buildings, the expert installer, after completing installation must verify that this onad been performed correctly and. Subsequently, it is necessary to instruct the user on the correct use of the product providing all the documentation envisaged.

Este manual ha sido redactado por el constructor y forma para integrante del producto. Las informaciones que contiene van dirigidas a los operadores.

APRIMATIC INDIANAPOLIS ONDA KIT AUTOMAZIONE CANCELLO SCORREVOLE SCORREVOLI | eBay

Add to my manuals Add. Page 5 The wheels must match the arimatic profile and must be in good condition. Page 7 With wooden gates, it is better to use the plastic rack by verifying the good conditions of the wood in the fixing points.

Page 9 A description is also given of the typical layout that must be controlled when the site is inspected see also fig. Page 13 The A measurement depends on the type of pinion and the type of rack used see tables in C Page 16 C 19 Spirit level C 20 Rest the first rack section on the geared-motor pinion and move the spacers in contact with the gate until the first hole complete with screw and spacer is lined up with the vertical axis of the pinion C19then fix the spacer to the gate with a spot weld.

wechwech Recherche

Page 21 The adjustment of the clutch and all the safety devices must be per- formed only by qualified personnel. Page 25 The release system that disengages the pinion allows the manual opening of the gate.

Page 26 Installation instructions Page 27 To avoid incorrect manoeuvres and the consequent risk of accidents, it is important to read this manual carefully, strictly observing the instructions given. Page 28 Device with Aprimatic microprocessor 15 Watt in stand-by designed to drive 1 motor with a maximum power of Watt.

Page 31 3 seconds and aprjmatic closing. This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an account?